计算机科学 ›› 2018, Vol. 45 ›› Issue (6A): 576-579.

• 综合、交叉与应用 • 上一篇    下一篇

汽车喷油器噪声测量系统的设计

朱均超,王坦,张宝峰   

  1. 天津理工大学电气电子工程学院 天津300384
  • 出版日期:2018-06-20 发布日期:2018-08-03
  • 作者简介:朱均超(1972-),男,副教授,硕士生导师,主要研究方向为检测装置与检测技术,E-mail:zhujunchao@tjut.edu.cn;王 坦(1993-),女,硕士生,主要研究方向为传感技术与自动化检测,E-mail:492055384@qq.com(通信作者)。

Design of Noise Measurement System for Automobile Injector

ZHU Jun-chao,WANG Tan,ZHANG Bao-feng   

  1. School of Electrical and Electronic Engineering,Tianjin 300384,China
  • Online:2018-06-20 Published:2018-08-03

摘要: 针对国内外相关标准对喷油器噪声测量技术的要求,设计了一套汽车喷油器噪声测量系统。该系统包括喷油器驱动模块、系统控制模块、系统供油模块、噪声测量模块和人机交互模块。供油模块的压力控制采用薄膜传导结合PID反馈的气动调节方式,提高了压力控制的可靠性和精度;系统软件设计采用Windows VS2010开发平台,利用CAN通讯、RS232等串口通讯技术以及多线程并行技术实现人机交互界面对喷油器工作噪声检测系统的整体控制;基于声压法对汽车喷油器的噪声进行测量和分析,依据测量结果对喷油器的性能进行评价。经实验验证,A计权下的最大声压级和平均声压级均小于标准中的70db(A),满足标准对汽油机喷油器噪声值的要求。

关键词: PID算法, 喷油器, 压力控制, 噪声测量

Abstract: Aiming at the technical requirements of injector noise measurement at home and abroad,a set of noise mea-surement system for automobile injector was designed.The system includes an injector drive module,a system control module,a system oil supply module,a noise measurement module and a man-machine interaction module.The pressure control of oil supply module adopts the pneumatic control method of the membrane conduction combined with the PID feedback to improve the reliability and the precision of pressure control.The system software is designed by using the Windows VS2010 development platform.Using CAN communication,RS232 serial communication technology and multi-thread parallel technology,the whole control of man-machine interaction interface to the noise detection system of injector is achieved.Based on the sound pressure method,the noise of the fuel injector is measured and analyzed,and the performance of the injector is evaluated according to the measurement result.Experimental results show that the maximum sound pressure level and average sound pressure level under A weighting are less than 70db (A) in the standard,meeting the requirements of the standard on fuel tanker’s noise value.

Key words: Injector, Noise measurement, PID algorithm, Pressure control

中图分类号: 

  • TH89
[1]杨金才,杨金榜,丁艳萍,等.发动机喷油噪声控制方法的研究[J].汽车工程,2011,33(10):898-901.
[2]ANDRIANOV D I,MANZIE C,BREAR M J.Spark ignition engine control strategies for minimizing cold start fuel consumption under cumulative tailpipe emissions constraints[J].Control Engineering Practice,2013,21(8):1007-1019.
[3]ROBERTS A,BROOKS R,SHIPWAY P.Internal combustion engine cold-start efficiency:A review of the problem,causes and potential solutions[J].Energy Conversion and Management,2014,82:327-350.
[4]刘瑞骏,郝志勇,郑旭,等.自适应广义S变换汽油机怠速振动分析[J].浙江大学学报,2016,50(3):43-50.
[5]PAYRI R,GARCIA J M,SALVADOR F J,et al.Using spray momentum flux measurements to understand the influence of diesel nozzle geometry on spray characteristics[J].Fuel,2004,84(5):551-561.
[6]孙宜权,王滨,张英堂,等.基于自适应平行因子的柴油机喷油故障诊断研究[J].兵工学报,2013,34(5):30-34.
[7]褚志刚,蔡鹏飞,蒋忠翰,等.基于声阵列技术的柴油机噪声源识别[J].农业工程学报,2014,30(2):23-30.
[8]罗福强,周群,薛福英,等.农用柴油机喷油器各孔喷油规律验证及流动特性模拟[J].农业工程学报,2016,32(2):58-63.
[9]仇滔,冯祥,雷艳,等.出口压力对柴油喷油器流量特性影响的实验研究[J].兵工学报,2015,36(5):33-36.
[10] HATTOR H,NARUMIYA K.Analysis of initial breakup me- chanism of diesel spray injected into high-pressure ambience[C]∥SAE 2014 World Congress & Exhibition.2004.
[11] 刘凯敏,杨靖,朱继明,等.涡轮增压直喷汽油机变速器噪声的试验研究[J].汽车工程,2016,38(4):33-38.
[12] 李梅林,谢惠民.车用发动机噪声测试研究[J].湖南大学学报,2004,31(3):28-31.
[13]刘帅,王忠,王林,等.柴油机表面辐射噪声源识别与降噪研究[J].汽车工程,2016,38(9):33-38.
[14] 王谦,孙伟,何志霞,等.基于超高速摄影分析柴油机近场喷雾锥角变化特性[J].农业工程学报,2016,32(15):47-53.
No related articles found!
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!